Expert Answers about GMC Hitch Cargo Carrier

• Cargo Bag Recommendation to Use with Curt Cargo Carrier C18145
• The etrailer cargo bag part # e98990 would be a great option for your Curt cargo carrier part # C18145 as it's size is close to the internal dimensions of the carrier and it's water resistant. This will do a great job keeping your cargo dry under normal driving circumstances.
  view full answer...


• Factors that Contribute to Exhaust Melting Hitch Cargo Carrier
• Exhaust melting cargo on a cargo carrier isn't a super common problem, but we are aware that it does happen on occasion. Especially if the cargo carrier is at the same height as the exhaust, relatively close to it, and/or the material in the carrier is susceptible to melting. Other factors to consider are the size of the engine, climate, and road conditions. Engines are basically big air pumps. The bigger the motor the more hot air is pumped out of it. Hotter climates will also allow things...
  view full answer...


• How to Reduce Wobble when Using Curt Cargo Carrier C18145 in a 2 Inch Trailer Hitch
• Hitch accessories tend to wobble, especially those that use a 1-1/4 inch to 2 inch adapter. The threaded hitch pin can only do so much to combat the movement. The issue is that the shank of the accessory has to be slightly smaller than the opening otherwise it would be difficult to insert and remove the accessory. That combined with the single attachment point and width of a cargo carrier means that even the smallest gap between shank and receiver seems huge at either end of the carrier. What...
  view full answer...


• Installing the LED Light Kit # 98174LED in the Rola Hitch Cargo Carrier # 59502
• I went out to the warehouse and got a set of lights and a cargo carrier. When I attempted to install the grommets and lights in the light mounting cut outs they fit well but you must get the grommet all of the way into the mounting hole. I took the grommet, installed it into the cargo carrier then pressed the light into the carrier. Make sure the grommet snaps in fully. I started on one end of the grommet and pressed it in until it snapped in fully, causing the face of the grommet to flatten...
  view full answer...


• How to Level Out Rear Sag on a 2018 Toyota Sequoia SR5
• Ideally you're staying under the weight capacity of the hitch on your 2018 Toyota Sequoia SR5, but if the weight of the carrier and cargo is more than what the tongue weight of your trailer hitch is rated for then that would be why it looks like your hitch is overloaded - because it is. If you're within your weight capacity then you could just be seeing the stress of the weight taking a toll on the rear suspension of your vehicle and to remedy that we have the Air Lift 1000 Air Helper...
  view full answer...


• Troubleshooting GearSpace 34 with Hitch Extender Sagging on 2020 Mercedes-Benz Sprinter 3500
• From the pictures you sent it looks like your setup is overloaded. It is important to remember that the use of an extender like this will reduce the capacity of your hitch by 50%. That means if you have a hitch like the Curt # C13388, your maximum tongue weight has been reduced from 600 lbs to 300 lbs. If your hitch has a 500 lbs maximum tongue weight it will be 250 lbs with the extender. According to the manufacturer, the minimum tongue weight rating for your hitch must be 350 lbs in...
  view full answer...


• Troubleshooting Hitch Lock on SportRack SR2415 and a 2017 Toyota Tacoma
• The SportRack Ridge Swing 4 Bike Rack # SR2415 has the Anti-Rattle Hitch Lock for SportRack Bike Racks and Cargo Carriers - 1-1/4" and 2" Hitches # SR0901 as you referenced as a related part. I have not heard about this not working on this rack before and that is the longest locking pin available for that rack, which makes me wonder if your trailer hitch receiver is uniquely wide. If so, you may want to consider using an adapter for the rack like Hitch Extender for 2" Trailer Hitches...
  view full answer...


• Can The Lock Assembly Be Replaced On A Sears Sport 15-CAV Cargo Carrier?
• I spoke with Thule and they said that they do not have a lock assembly available for the Sears Sport cargo carriers since all of those cargo carriers were manufactured with a riveted lock assembly, which has never been an available part. The Replacement Lock Core and Key for SportRack Explorer Cargo Box # SR03807 that you were advised to purchase will only work with the Sidekick Carrier TH682 which is no longer available. Seeing as though you can't get a replacement lock, you may consider...
  view full answer...


• Recommendation for Taking Play Out of Curt Cargo Carrier # C18153
• The only solution I could recommend for you would be to use a stabilizer strap like part # 18050. You would run one end of the strap to the top seam of your trunk/hatch on your vehicle and the other end to the carrier so that tension in the strap will prevent the carrier from moving as much. I attached a review video for the strap for you to check out to show you how it works.
  view full answer...


• Suspension of 2008 Honda Pilot Squats When Cargo Carrier is Installed
• So, what you are saying is that once the cargo carrier is loaded up with whatever you are carrying, the rear suspension compresses quite a bit, is that correct? If this is the case, it sounds like you would be a good candidate for a rear suspension enhancement kit. For a passive system that would only come into play when extra weight is applied to the rear of the vehicle, like when the carrier is being used, the Timbren # THROD2 system would be great. Install the system, and you would...
  view full answer...


• Hitch Pin Holes Not Lining Up Using MaxxTow Hitch Extender and Draw-Tite Class III Trailer Hitch
• I spoke with my contact at Draw-Tite and he said that on the Draw-Tite trailer hitch # 75270 you will want to use the 5/8 inch pin hole which is the one closest to the crosstube. The pin hole closest to the trailer, a 1/2 inch pin hole, is not used at all. Based on my measurements you will need an extender that is at least 6-1/2 inches from the pin hole to the back of the receiver. Unfortunately we do not carry any extenders that length. Your best bet may be to go with a cargo carrier...
  view full answer...


• SportRack Anti-Rattle Hitch Lock Will Not Lock
• What might be happening with your Anti-Rattle Hitch Lock for SportRack Bike Racks and Cargo Carriers # SR0901 is that your hitch receiver might be too thick which is not allowing you to get the lock on enough of the threaded pin to lock it. You can test this out by uninstalling the threaded hitch pin (if it is installed) and trying to install the locking mechanism onto the pin. If it attaches then you know that your hitch receiver it too think and you will not be able to use the locking...
  view full answer...


• Is it a Good Idea to Use More Than One Hitch Adapter?
• Here at etrailer, we do not recommend using two hitch adapters at the same time. Not only does it reduce the weight capacity of the hitch even more (more than the 50% from using one adapter), it can be dangerous for other motorists. In addition, we also don't recommend using the adapter backwards. For this situation, I suggest eliminating the second adapter.
  view full answer...


• Replacement Key for Older Sears X-Cargo 2802
• Yes, for your Sears X-Cargo box with a lock core that has 2802 the correct key is the part # THKEYN2802.
  view full answer...


• Troubleshooting Running Lights not Functions with a Cargo Carrier Light Kit # 20174
• The first thing I would recommend you do is test the running light circuit of your 7-way minus any of the adapters to determine if there is voltage there and then put the adapter on and test the running light circuit there also. This will tell you if the problem happens to be on the wiring or adapter. If the voltage is good then the problem lies somewhere in the # 20174 wiring. I attached an FAQ article on trailer wiring that you might find helpful also. I also attached a link to a...
  view full answer...


• Trailer Lights on a Cargo Carrier Flash Rapidly with Brake Applied on a 2008 Harley Ultra Classic
• It sounds like the lights are hyperflashing. This normally occurs with LED lights. You can try moving the grounds for the lights to the carrier. If the connector on the bike is set up for separate turn signals and brake lights but the lights you added are designed for a combined brake and turn signal, that could be the problem.
  view full answer...


• How do I Decrease Sagging with the GearSpace 34 on My 2022 Mercedes Sprinter 3500?
• If you have sagging when using the GearSpace 34 # HGK826 on your 2022 Mercedes Sprinter 3500, the first thing to do is to make sure that you are abiding by the weight capacity of the carrier and the hitch itself. The carrier has a weight capacity of 300 pounds, so it is important to make sure that you are not overloading the carrier. Secondly, it is important that you don't overload the hitch itself. Since the GearSpace 34 weighs 160 pounds, that weight needs to be added to the weight of...
  view full answer...


• Troubleshooting Replacement Key for Sears Sport 20-SV Cargo Carrier
• As long as the lock core on your Sport 20-SV Cargo Carrier is printed with the number 2826, the # THKEYN2826 should be the correct replacement key. I recommend checking to make sure the lock core is clean and free of any debris/corrosion that might be preventing the key to insert all the way. Sometimes there are also some issues with replacement keys going in smoothly during the first use. In these cases, they just need a little persuasion and you can gently tap it with a mallet to get...
  view full answer...


• Can Using the Flint Hill Goods 60" x 22" Cargo Carrier Obstruct Your License Plate
• Yes, when using the Flint Hill Goods 60" x 22" Cargo Carrier # FHG49ZR your license plate could be obstructed by the cargo that you are carrying. But never fear, a solution is near. You can use the Thule License Plate Holder # TH35JV to relocate your license plate to the outside of the cargo carrier, allowing it to be visible. And the Thule License Plate Holder # TH35JV features a light to provide visibility at night. If you are interested in adding lights to the Cargo Carrier # FHG49ZR...
  view full answer...


• Will Curt Hitch C11522 Interfere With The Rear Automatic Tailgate Feature?
• One of my contacts at Curt Manufacturing advised me that, the Curt Trailer Hitch Receiver Custom Item # C11522 is compatible with the automatic tailgate sensors on the 2018 Mini Countryman. This trailer hitch is perfect for light-duty towing, this custom, vehicle trailer hitch receiver features fully welded, gloss powder coated steel construction.. Please note: all non-trailer loads - bike racks, cargo carriers and so forth - should be supported with stabilizing straps # 18050. Failure...
  view full answer...